Rodder Accessories pg3
Roller Guide
Helps guide the duct rod around bends, sweeps, and duct misalignments.
Also used when the conduit is already occupied by other cables.
| Rod Dia., In (mm) | 3/16 (5) | 1/4 (6) | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| USC Thread | #12–24 | 5/16 –18 | 3/8 –16 | 3/8 –16 | 3/4 –10 |
| Roller Guide | 08037430 | 08037440 | 08037401 | 08037401 | 08037400 |
| Metric Thread | M5 | M8 | M12 | M12 | M12 |
| Roller Guide | 08037428 | 08037450 | 08037405 | 08037405 | 08037405 |
Shackle Fitting
Fits onto tapered head to provide a larger pulling loop for attaching the rope or pull line.
| Rod Dia., in (mm) | 3/16 (5)* | 1/4 (6)* | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| USC Thread | #12–24 | 5/16 –18 | 3/8 –16 | 3/8 –16 | 3/4 –10 |
| Accessory Kit | - | - | 08031101 | 08031101 | 08031100 |
| Metric Thread | M5 | M8 | M12 | M12 | M12 |
| Accessory Kit | - | - | 08031101 | 08031101 | 08031101 |
Sonde Adapter
Couples a locating sonde or other device with an M10 male thread to the male end fitting of the duct rod.
| Rod Dia., In (mm) | 3/16 (5) | 1/4 (6) | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| Kit | 08033457 | 08033465 | 08035753 | 08035751 | 08035752 |
| Splice Tube | 08033455 | 08033463 | 08035703 | 08035701 | 08035702 |
Swivel Coupling
Used to connect two duct rods pushed into the conduit from the same end. Used when one length of duct rod is not long enough for the full conduit run. Also used as a rotating swivel when pulling wire or rope with the tapered head or mini-harness.
| Rod Dia., In (mm) | 3/16 (5) | 1/4 (6) | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| USC Thread | #12–24 | 5/16 –18 | 3/8 –16 | 3/8 –16 | 3/4 –10 |
| Female/Female | 08033470 | 08033459 | - | - | - |
| Male/Female | 08033422 | 08033442 | 08036800 | 08036800 | 08036700 |
| Metric Thread | M5 | M8 | M12 | M12 | M12 |
| Female/Female | 08033429 | 08033483 | - | - | - |
| Male/Female | 08033426 | 08033485 | 08036806 | 08036806 | 08036806 |
Tapered Head
Attaches to the end fitting on the duct rod. Guides duct rod through the conduit and allows a pull line (diameter A) to be attached to the duct rod. Comes standard with each of the duct rodders.
| Rod Dia., In (mm) | 3/16 (5) | 1/4 (6) | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| USC Thread | #12–24 | 5/16 –18 | 3/8 –16 | 3/8 –16 | 3/4 –10 |
| Tapered Head | 08033421 | 08033441 | 08038400 | 08038400 | 08038300 |
| Diameter A | .156 (4) | .156 (4) | .281 (7) | .281 (7) | .343 (9) |
| Metric Thread | M5 | M8 | M12 | M12 | M12 |
| Tapered Head | 08033410 | 08033480 | 08038301 | 08038301 | 08038301 |
| Diameter A | .156 (4) | .156 (4) | .281 (7) | .281 (7) | .281 (7) |
Basket Combination
Used to connect two duct rods pushed into the conduit form opposite ends of the conduit run. Both rods can then be pulled out in one direction. Used instead of a swivel coupling when the full length of the rod is difficult to push from one end. Works in 4" (102 mm) or larger conduit only. Does not negotiate tight bends.
| Rod Dia. in (mm) |
3/16 (5) | 1/4 (6) | 5/16 (8) | 7/16 (11) | 9/16 (14) |
| USC Thread | #12–24 | 5/16 –18 | 3/8 –16 | 3/8 –16 | 3/4 –10 |
| Mini Harness | - | - | 08031400 | 08031400 | 08031300 |
| Metric Thread | M5 | M8 | M12 | M12 | M12 |
| Mini Harness | - | - | 08033700 | 08033700 | 08033700 |